-
Home
- Audi TT-RS / RS3
- Loba-Motorsport
- Accusump/ Drysump/oilpan
-
AN connections
- AN slang
- Push On Slang
- AN-4
- AN-6
- AN-8
- AN-10
- AN-12
- AN-16
- För direkt röranslutning
- Strigt Banjo
- Stright Male
- Rak JIC (AN) x NPT
- 45° JIC (AN) x NPT
- 90° JIC (AN) x NPT
- Rak JIC (AN) x NPT
- "Push On" Rak JIC (AN) IR
- "Push On" 45° Böj JIC (AN) IR
- "Push On" 90° Böj JIC (AN) IR
- "Push On" 150° Böj JIC (AN) IR
- "Push On" 180° Böj JIC (AN) IR
- AN Cap
- AN Plugg
- Banjoadapter
- NPT x NPT Inv.”Muff”
- Mutter
- Stödhylsa
- NPT x NPT Uf x Uf
- NPT If x NPT Uf Reducering
- Plugg NPT Insex
- JIC / mm Conv.
- JIC / mm konkav
- 90° NPT x NPT If x Uf
- 45° NPT x NPT If x Uf
- 90° NPT x NPT If x If
- T NPT x NPT If x If x If
- JIC (AN) x NPT på Stolpen
- TJIC (AN) x NPT på Sidan
- 90° JIC (AN)
- T JIC (AN)
- JIC (AN) Skarv Oliksidig
- JIC (AN) Skarv
- 45° JIC (AN) Skottgenomgång
- 90° JIC (AN) Skottgenomgång
- T JIC (AN) Skottgenomgång på Sida
- T JIC (AN) Skottgenomgång på Stolpen
-
Fuel
-
Brakes
- Bolt/Nut
-
Chassis
- Blow Off Valve
- Electrical System
- Exterior/Lighting
-
Filter
- CLEARANCE
- Intake manifold
- Cooling
- Carbon Fiber And Kevlar
- Chemical articles
-
Clutches/ Transmission accessories
- Cooling
- Air/ Vacuum
-
Engine parts
- Bolt/Nut
- Distributor
- Sensors
- Girdle
- Camshaft
- Cam gear
- ARP bolts
- Piston
- Piston rings
- Main bearings
- Tappets
- Oil cap
- Cooperring gaskets
- Oilpump
- Gaskets
- Retainer
- Custom parts
- Water pump
- Valve
- Valve spring
- Crankshaft
- Connecting Rod
- Hose / Hose-connections
- Oilpan
- ACL-Bearings
- Topplock
- Vevhusventilation
- Engine cover
- Engine Mounts
- Svängningsdämpare
- Motorelektronik
- Engine management systems
-
Nuke Performance
- Oils/Liquids
- Belts/tensioner
- Hoses
- Supertech
- Turbo
- Ignition
- Tools
- Exhaust Wrap
- Wagner-Tuning
- Wastegate
- 034 Motorsport
- 07K 5 cylinder engine
- Easthill / VW / Old School
- Auto-Verdi
- ARC-Zone
- Boostane
- Categories
- Kategorier
-
SWEDENEXHAUST
- CLEARANCE
- Special prices
- All brands
- Kategorier
- Home
ARP BMW 2002 (M10), 318i, 320i Head Stud Kit
Fits BMW M10 engine
(edit with the Customer Reassurance module)
(edit with the Customer Reassurance module)
(edit with the Customer Reassurance module)
Delivery time 2-10 days
INSTALLATION METHOD FOR HEAD STUD KITS
200,000 PSI 12 mm Diameter
1. To ensure proper thread engagement and accurate torque readings, clean ALL threads in the block. Chase if
necessary with ARP Thread Chaser.
2. Clean and inspect all hardware prior to installation. Look for obvious defects or shipping damages, plus proper fit,
length and dimension.
3. If the cylinder head studs protrude into a water jacket, lubricate the block threads of the studs with ARP
THREAD SEALER.
4. Screw studs into the block “HAND TIGHT ONLY”.
NOTE: LOCTITE MAY BE USED IF A PERMANENT MOUNTING OF THE STUDS IS PREFERRED. THE
FASTENERS, HOWEVER, MUST BE TORQUED PRIOR TO THE LOCTITE SETTING UP.
5. Install the cylinder head(s) and check for binding or misalignment.
6. Lubricate the stud threads, nuts and washers with ARP ULTRA-TORQUE FASTENER ASSEMBLY LUBRICANT.
Then install the washers and the nuts onto the studs and tighten them hand tight. ARP recommends using the
ARP ULTRA-TORQUE FASTENER ASSEMBLY LUBRICANT that is provided with each kit as opposed to
motor oil. This is due to higher friction on the studs as well as inconsistencies in the clamping force of
the fasteners when motor oil or other low quality lubricants are used.
PRELOAD (TORQUE) RECOMMENDATIONS
7. Following the manufacturers recommended torque sequence tighten the nuts in three equal steps to 90 ft lbs
with ARP ULTRA-TORQUE FASTENER ASSEMBLY LUBRICANT.
Note: ARP Ultra-Torque Fastener Assembly Lubricant has been specifically designed to reduce tension preload scatter and
eliminate the need to cycle high performance engine fasteners before final installation. ARP Ultra-Torque far surpasses all
requirements offered by previous ARP lubricants in terms of fastener preload repeatability and performance lubricating
properties.